Skorpion substitute part database- please add!

[Lebowski]

I replaced my rear master cylinder with one from a Ducati Monster,
also the replaced the taillight lens with one from a '90s Monster.
I have a '95 Skorpion tour.

[Whysub]

KTM 690 has the same radiators as the Bhagira. The KTM radiator shrouds also fit straight on.

Yamaha TZR125 rear light fits the Baghira.

[Chuck in Indiana]

Guzzi spine frames use the same tail light and turnsignals as my 95 Tour.

[DAVID THOMPSON]

years and models would help

a lot of us have no clue what a Guzzi spine frames is
i my self have been riding over 60 years and have never rode one
and once in a while i see one
its over 220 mile round trip to the nearest dealer

dave

[Chuck in Indiana]

years and models would help

a lot of us have no clue what a Guzzi spine frames is
i my self have been riding over 60 years and have never rode one
and once in a while i see one
its over 220 mile round trip to the nearest dealer

dave

Oh, sorry. That would be the 97 V10 Centauro through the 05 V11 Sports. Dealer? Don't need no steenkin dealer.. Wish I had a local dealer like that..
Seriously, Guzzi parts are a walk in the park to get, even for some really old stuff.
The turnsignals are also the same as Buell, as is the headlight and trim ring on the Skorpion tour.

[ralf]

This is so valuable ! Is there any way we could get it on the site as a proper database rather than individual posts. That way it could be categorised (electrical, rear suspension, brakes ....... etc) and be so much more useful. Perhaps the moderators could advise ?

[ralf]

Rubber tops for footpegs are Yamaha TRX.

[Kcfirebolt]

Anyone know of a source for the rubber chain guide that protects the swing arm? I've rigged up a piece of polyurethane, but I'm not sure that I'm completely comfortable with it's security.

[tigcraft]

Rubber tops for footpegs are Yamaha TRX.

Strangely enough I've one of those too and your right. Eric

[barko1]

My throttle hand assembly can't be tightened enough, guess the plastic threads are strippe. I think the whole right hand switch unit needs replacing. I imagine there is a Yamaha part?? Can't find one in any schematics, any alternatives?

[Dicer]

My throttle hand assembly can't be tightened enough, guess the plastic threads are strippe. I think the whole right hand switch unit needs replacing. I imagine there is a Yamaha part?? Can't find one in any schematics, any alternatives?

Mine is the same. I'd like to know the answer too.

[DAVID THOMPSON]

switch gear look in this catalog

http://www.sudco.com/CatalogDigital.html

http://www.sudco.com/Catalog37Digital/index.html#/484/

http://www.sudco.com/Catalog37Digital/i ... 484/zoomed
hope this link works

dave

[Chuck in Indiana]

My throttle hand assembly can't be tightened enough, guess the plastic threads are strippe. I think the whole right hand switch unit needs replacing. I imagine there is a Yamaha part?? Can't find one in any schematics, any alternatives?

Mine is the same. I'd like to know the answer too.

My Skorpion's switch gear was stripped on all 4 screws. I just filled the holes with JB weld, and drilled and tapped them. Pretty simple to do, cheap. (Guzzi content)

[Dicer]

Thanks Chuck, if that does the job, it's worth a try. It just didn't look like those tiny screws would hold it firmly though.

[Chuck in Indiana]

Thanks Chuck, if that does the job, it's worth a try. It just didn't look like those tiny screws would hold it firmly though.

Not a problem. Take a toothpick and work the epoxy down into the hole. Just do the best you can. Drill& tap, and you'e golden.